How to install MarketAir rough-in boxes

  • Install Lineset and Cable First, line up the RoughinBox base with the mark on the studs. Insert the box in between the studs and attach it in place by using the four integral mounting brackets.



MarketAir RoughinBox Installation

Preparing the RoughinBox

Select 1/2 inch or 1/4 inch port as needed when you are using a cable port. Now, you have to cut as X marked on the top of the port with a utility knife and push the cable through the opening. This will create an integral strain relief bushing for preventing the cable from pulling out by itself.

If your box includes five lineset ports one on each end, one on the bottom, and two on top. For the bottom or top line ports, line sets from the evaporator should run from right to left so facing front of RoughinBox. You have to try always to bring lineset into the box from the left to avoid a difficult connection to the evaporator. Make sure that you keep lineset entry orifice as small as possible by using the cut lines available on top of the line port cap. Do not cut below the marked line as it damages the slot which retains the mounting adaptor.

Do not remove the closure cap at end of the drain outlet when you are using a condensate pump. For gravity drain, the box has a bi-directional drain outlet with 1/6" MIPT threads which offers two choices, i.e., side discharge and bottom discharge. You can check the owner's manual to get complete details on this.

Remove all four mounting adaptors from slots at both ends of the box and invert them. So, you have to fix holes on the top face up and fix holes on the bottom face down and replace them with the same slot.

Check brands installation instructions to find the minimum distance between evaporator and ceiling and you can note these dimensions on studs. Generally, the recommended minimum dimension between baseline and ceiling is 20 inches. Later, position the mini-split rough in the new construction box correctly with the evaporator and mark studs accordingly.

If studs are metal, you need to determine which end of the box will face the open side of the stud. Also, extend mounting adaptors on that end to their full length of 1 1/8 inches so that they reach the stud to touch flat surfaces and lock them into the position. If studs are wood, you no need to extend the mounting adaptors and can use them for fixing.

                        https://www.partsxp.com/marketair

Comments

Post a Comment

Popular posts from this blog

4' 40 Amp 4 Wire Range Cord By GE General Electric Hotpoint - Part# WX09X10035

Image
  The  4' 40 Amp 4 Wire Range Cord, part number WX09X10035 , is a product manufactured by  GE  (General Electric) and is also compatible with Hotpoint ranges. This range cord is designed to provide a safe and secure connection between an electric range or stove and the electrical outlet. Here are some key features and details about the GE WX09X10035 range cord: Length and Gauge: The cord is 4 feet long, providing sufficient length for most installations. The wire gauge is rated at 40 Amps, making it suitable for ranges that require this amperage. Wire Configuration: The cord features a 4-wire configuration, which includes four conductors: two hot wires, one neutral wire, and one ground wire. This configuration is commonly used for electric ranges and stoves and is required for proper and safe operation. Compatibility: The WX09X10035 range cord is compatible with a wide range of electric ranges and stoves manufactured by GE, General Electric, and Hotpoint. It is essen...
Read more

Appliances Parts and Supplies- PartsIPS

Image
  In the hustle and bustle of modern life, our household appliances stand as silent sentinels, making our daily routines smoother and more convenient. From the trusty refrigerator that keeps our groceries fresh to the washer and dryer that ensure our clothes are clean and ready, these machines are our everyday heroes. However, like any hero, they can face challenges, and this is where PartsIPS steps in. The Crucial Role of Appliance Parts: Appliance parts  are the unsung heroes behind the scenes, ensuring our appliances operate seamlessly. PartsIPS recognizes this significance and provides an extensive collection of components catering to a diverse range of appliances, from essential kitchen devices to laundry companions. From the most intricate circuitry to the smallest screws,  PartsIPS  offers a comprehensive selection to ensure no appliance repair remains a puzzle. The Authenticity of OEM Parts: In a world full of options, Original Equipment Manufacturer (OEM) pa...
Read more

DANBY PORTABLE WASHER TROUBLESHOOTING - PARTSIPS

Image
Occasionally a problem may arise in your Danby portable washer that is minor in nature and a service call may not be necessary. Some issues are easy fixes and others may require the service of a professional. However, with a little bit of troubleshooting, you will be able to at least have an idea of where the problem has existed Washing Machine Doesn’t Turn On Not plugged In The first step is to check the plug socket. The plug might be loose. Make sure the unit is plugged in firmly and there are no exposed wiring problems. If all these are fine, but still not working, plug in other appliances to determine whether the problem is with the circuit breaker or fuse. You can try to plug the portable washer into another socket and verify if that socket helps. Issues with power cord You have to see the power cord of the Danby portable washing machine for faults. If you notice any exposed wires or heavily frayed areas, you will need to replace them. If you are unable to do the replacement, con...
Read more