Installation of CreeZr24

 Cree Lighting offers ZR series LED troffer that gives you a broad portfolio of efficient and excellent light performance at an affordable price. This ZR series also provide a room-side removable lens with magnetic fasteners for easy access and maintenance. So, now, in this blog, we are going to discuss Cree ZR24 installation to make your job easier.



Cree ZR24 Installation Guide

Before you start Cree ZR series installation, you should read the below safety instructions.

Safety Instructions

  • Make sure you disconnect power before installation.
  • The luminaire needs to be installed by following the NEC or your local electrical code. If you are not familiar with these codes, it's good to contact a qualified technician.
  • ZR24 should be suitable for damp locations.
  • Don't install insulation within three inches of any part of the luminaire.
  • The vapor barrier must suitable for 90 degrees Centigrade.
  • It should be inherently protected.
  • Do not use wet hands for handling energized modules. Also, don't handle it when you are standing on wet/ damp surfaces or in water.

Bar Ceiling Mounting

First, bring the Cree ZR troffer into the T-bar ceiling panel. Find the location of the T-bar clips on the end panels of the troffer by referring to the figures in the manual.

After that, bend clips upward and rotate outward to engage with the T-bar support grid. Then, secure luminaire to grid according to the state and local codes.

Suspended Mounting

You need to attach the supplied cables to the T-bar clips which are located in the corners of the housing. You have to use the hole in each clip to attach the cable.

Now, connect the cables to the mounting surface with customer-supplied hardware. Make sure that the mounting surface supports the luminaire.

SmartCast Setup

Cree Lighting recommends reviewing the Cree Lighting SmartCast technology wireless deployment guide before installing luminaires with Cree Lighting SmartCast technology. Moreover, you must install SmartCast luminaires on unswitched AC power. To maintain all luminaires on the Smartcast network, constant power is needed.

Before installation, you have to disconnect power to the circuit by turning the circuit breaker OFF.

Next, remove the screw on the junction box cover and bring it to an appropriate power supply to the junction box using one of the knock-outs.

Wire luminaire per electrical connections section and push all leads into the junction box. Now, reattach the junction box which you have removed before. Ensure that no wires are pinched. Switch the circuit breaker on.

When the circuit breaker is ON, there should be a WIM blue LED that has a double-blink pattern. If you can't find this, know the troubleshooting tips to fix the issue. Also, there will be a chance to get more details through SmartCast documentation.

Reset

Once, you have done all the above Cree ZR installation processes, you need to reset the system.

Find the "reset" button through the access hole. Press and hold that button until your LED flashes fast for 5 seconds.

After that, you need to release it for a second. While fast flashing continues, press and hold the reset button for one second until the flashing stops. Check if the blue LED is responding with two blink sequences. If it doesn't respond, you will need to repeat the reset process again.

If the light is unresponsive, verify the configuration by using the Cree lighting configuration tool.

Cleaning LENS

To clean the lens, first, you have to locate the end cap with the arrow marks on LED that indicate that the end cap is removable.

Grab the lens section next to the end cap. Pull the lens as well as the end cap together downward until the end cap just clears the luminaire. You have to pull them about 3 to 4 inches from the original position.

Next, disengage the other end of the lens from the opposite end cap by pulling the lens away from the end cap. Once the lens is removed, you need to perform cleaning.

After completion of cleaning, you have to reinsert the lens into a fixed end cap. Push the removable end cap upward into the housing. And, use a gentle rock motion for engaging the end cap to retention clip.

Now, check the removable end cap for any visible gap between the end cap and end panel. If there are any gaps found, it's necessary to push the end cap against the end panel for removing gaps.

Inspect the lens for any visible gap between the lens and luminaire. Push lens upward at gap location to seal magnetic foam to luminaire if there are gaps.

If you have any further queries related to Cree Lighting ZR24 installation, check the Cree manual once.

Comments

Post a Comment

Popular posts from this blog

4' 40 Amp 4 Wire Range Cord By GE General Electric Hotpoint - Part# WX09X10035

Image
  The  4' 40 Amp 4 Wire Range Cord, part number WX09X10035 , is a product manufactured by  GE  (General Electric) and is also compatible with Hotpoint ranges. This range cord is designed to provide a safe and secure connection between an electric range or stove and the electrical outlet. Here are some key features and details about the GE WX09X10035 range cord: Length and Gauge: The cord is 4 feet long, providing sufficient length for most installations. The wire gauge is rated at 40 Amps, making it suitable for ranges that require this amperage. Wire Configuration: The cord features a 4-wire configuration, which includes four conductors: two hot wires, one neutral wire, and one ground wire. This configuration is commonly used for electric ranges and stoves and is required for proper and safe operation. Compatibility: The WX09X10035 range cord is compatible with a wide range of electric ranges and stoves manufactured by GE, General Electric, and Hotpoint. It is essen...
Read more

Appliances Parts and Supplies- PartsIPS

Image
  In the hustle and bustle of modern life, our household appliances stand as silent sentinels, making our daily routines smoother and more convenient. From the trusty refrigerator that keeps our groceries fresh to the washer and dryer that ensure our clothes are clean and ready, these machines are our everyday heroes. However, like any hero, they can face challenges, and this is where PartsIPS steps in. The Crucial Role of Appliance Parts: Appliance parts  are the unsung heroes behind the scenes, ensuring our appliances operate seamlessly. PartsIPS recognizes this significance and provides an extensive collection of components catering to a diverse range of appliances, from essential kitchen devices to laundry companions. From the most intricate circuitry to the smallest screws,  PartsIPS  offers a comprehensive selection to ensure no appliance repair remains a puzzle. The Authenticity of OEM Parts: In a world full of options, Original Equipment Manufacturer (OEM) pa...
Read more

DANBY PORTABLE WASHER TROUBLESHOOTING - PARTSIPS

Image
Occasionally a problem may arise in your Danby portable washer that is minor in nature and a service call may not be necessary. Some issues are easy fixes and others may require the service of a professional. However, with a little bit of troubleshooting, you will be able to at least have an idea of where the problem has existed Washing Machine Doesn’t Turn On Not plugged In The first step is to check the plug socket. The plug might be loose. Make sure the unit is plugged in firmly and there are no exposed wiring problems. If all these are fine, but still not working, plug in other appliances to determine whether the problem is with the circuit breaker or fuse. You can try to plug the portable washer into another socket and verify if that socket helps. Issues with power cord You have to see the power cord of the Danby portable washing machine for faults. If you notice any exposed wires or heavily frayed areas, you will need to replace them. If you are unable to do the replacement, con...
Read more