SolarEdge Backup Interface Installation - PartsXP

 

SolarEdge backup interface provides backup power automatically to home loads in the event of grid interruption. And, it is a scalable solution for supporting higher power and higher capacity. If you want to know how to install SolarEdge backup interface, continue to read this post. Here, we have explained SolarEdge backup interface installation instructions and how can you connect to the inverter, AC loads panel and grid.

A Guide on SolarEdge Backup Interface Installation

In the packet, you will get the following things:

Backup interface, conduit holder. mounting bracket, Allen key, accessories bag that contains two mounting bracket screws, bonding (for connecting the neutral & grounding bar) and one conduit holder screw and installation guide.

Buy SolarEdge Inverters at Very Low Cost!

ecobee

SolarEdge Backup Interface Mounting

Normally, the conduit entries are in the closed position with drill guides. You have to open them by drilling the conduit entries before mounting the backup interface. Now, check the mounting process of the SolarEdge backup interface.

  • Initially, you have to determine the backup interface mounting location. It would be on a wall, pole or stud framing. It's recommended to select a location that is protected from direct sunlight.
  • You should maintain a minimum of 4 inches clearance between the interface and other objects.
  • Position the mounting bracket against the pole or wall and mark the drilling hole locations.
  • Now, drill the holes as per marking and mount the bracket. Make sure to verify that the bracket is firmly attached to the mounting surface.
  • After that, you need to hand the SolarEdge interface on the bracket.
  • Next, insert the two supplied screws through the outer heat sink fin on both sides of the interface and into the bracket. And, tighten the screws.

Conduit Holder Installation

You have to install the conduit holder with the backup interface to firmly secure the grid and AC loads. Remember that you need to complete the conduit holder placement only after mounting the SolarEgde surface. Know how to install conduit holder.

  • Place the conduit holder in between the fins of the heat sink and mounting surface.
  • First, slide it to the left and then down to hang the holder on the shortfin and the bolt which is affixed to the outer left fin.
  • Next, mark locations on the mounting surface for drilling.
  • Then, you will need to remove the conduit holder.
  • Drills holes where you have marked before.
  • Now, install the conduit holder and tighten it to the mounting surface with two screws.
  • Tighten the conduit holder to the outer left fin as well with the supplied screw.

Shop SolarEdge HD Wave Inverters Online @ PartsXP.

ecobee

Backup Interface Interfaces

In this section, you can learn about the SolarEdge backup interface to operate & connect to other system components.

Inverter AC inputs - AC cables from up to three inverters.

Generator AC input - An AC cable from one external generator.

Loads AC output - AC cable to the loads panel.

Grid AC input - An AC cable from the grid.

Communication input - Communication cables from inverters and external rapid shutdown switch.

LEDs - Three LEDs indicate the system performance.

ON/ OFF switch - When this switch is ON, enables an automatic transition to backup mode. If it is OFF, enables manual control of the backup interface.

Connecting Backup Interface to the Grid & AC Loads Panel

Use the 4-4/0 AWG cable types for connecting the interface to the loads panel and grid.

  • Loosen the Allen screws of solaredge interface cover and remove the cover.
  • Next, you have to install a conduit of the required diameter into the loads/ grid conduit entry. For supporting the conduit, you can use the conduit holder.
  • After that, remove the plastic covers from loads terminals.
  • Connect the neutral and grounding bars with the bonding based on the requirement. And, tighten the bonding screws.
  • Keep the cable from the AC loads panel/ grid through the conduit.
  • Next, you will need to attach the neutral and ground wires to their respective terminals.
  • Connect L1 and L2 wires from the grid/ AC loads panel to the grid/ loads line terminal and tighten the screws.
  • Reinsert the removed plastic covers onto the loads terminals.

Premium Quality SolarEdge Products - Order Today!

ecobee

Connecting SolarEdge Backup Interface to the Inverter

To connect to the communication cable and 12V cable,

  • Place a conduit of the required diameter into the com 1 conduit entry.
  • Next, connect the required cables to the inverter's connection unit.
  • After that, you have to connect the cables to the solaregde backup interface.

Connecting Backup Interface to an External Rapid Shutdown Switch

You should install an external shutdown switch as it shuts down the backup interface in emergency conditions.

  • Insert the cable from the shutdown switch through the com 2 conduit.
  • Remove the two-pin connector which is labeled as EXT RSD. Also, remove the short circuit jumper from the 2-pin connector.
  • After that, connect that cable to the 2-pin connector as per instructions given in the manual.
  • Place the 2-pin connector back into its EXT RSD port.
  • Reinstall interface cover by tightening with screws.

ecobee

Once you have installed SolarEdge backup interface, you need to configure it using the SetApp mobile application. You can check the instructions for configuration in the product manual. If you have any queries regarding SolarEdge backup interface installation, refer to the manual or consult a professional.

Comments

Post a Comment

Popular posts from this blog

4' 40 Amp 4 Wire Range Cord By GE General Electric Hotpoint - Part# WX09X10035

Image
  The  4' 40 Amp 4 Wire Range Cord, part number WX09X10035 , is a product manufactured by  GE  (General Electric) and is also compatible with Hotpoint ranges. This range cord is designed to provide a safe and secure connection between an electric range or stove and the electrical outlet. Here are some key features and details about the GE WX09X10035 range cord: Length and Gauge: The cord is 4 feet long, providing sufficient length for most installations. The wire gauge is rated at 40 Amps, making it suitable for ranges that require this amperage. Wire Configuration: The cord features a 4-wire configuration, which includes four conductors: two hot wires, one neutral wire, and one ground wire. This configuration is commonly used for electric ranges and stoves and is required for proper and safe operation. Compatibility: The WX09X10035 range cord is compatible with a wide range of electric ranges and stoves manufactured by GE, General Electric, and Hotpoint. It is essen...
Read more

Appliances Parts and Supplies- PartsIPS

Image
  In the hustle and bustle of modern life, our household appliances stand as silent sentinels, making our daily routines smoother and more convenient. From the trusty refrigerator that keeps our groceries fresh to the washer and dryer that ensure our clothes are clean and ready, these machines are our everyday heroes. However, like any hero, they can face challenges, and this is where PartsIPS steps in. The Crucial Role of Appliance Parts: Appliance parts  are the unsung heroes behind the scenes, ensuring our appliances operate seamlessly. PartsIPS recognizes this significance and provides an extensive collection of components catering to a diverse range of appliances, from essential kitchen devices to laundry companions. From the most intricate circuitry to the smallest screws,  PartsIPS  offers a comprehensive selection to ensure no appliance repair remains a puzzle. The Authenticity of OEM Parts: In a world full of options, Original Equipment Manufacturer (OEM) pa...
Read more

DANBY PORTABLE WASHER TROUBLESHOOTING - PARTSIPS

Image
Occasionally a problem may arise in your Danby portable washer that is minor in nature and a service call may not be necessary. Some issues are easy fixes and others may require the service of a professional. However, with a little bit of troubleshooting, you will be able to at least have an idea of where the problem has existed Washing Machine Doesn’t Turn On Not plugged In The first step is to check the plug socket. The plug might be loose. Make sure the unit is plugged in firmly and there are no exposed wiring problems. If all these are fine, but still not working, plug in other appliances to determine whether the problem is with the circuit breaker or fuse. You can try to plug the portable washer into another socket and verify if that socket helps. Issues with power cord You have to see the power cord of the Danby portable washing machine for faults. If you notice any exposed wires or heavily frayed areas, you will need to replace them. If you are unable to do the replacement, con...
Read more